An Effect Of Pressure Bending In Single Mode Optic Fiber On Light Intensity Attenuation

  • Alfredo Bangkit H Parapat Universitas Pembangunan Panca Budi, Medan, North Sumatera, Indonesia
  • Solly Aryza Universitas Pembangunan Panca Budi, Medan, North Sumatera, Indonesia
  • Amani Darma Tarigan Universitas Pembangunan Panca Budi, Medan, North Sumatera, Indonesia
Keywords: Single-mode optical fiber, pressurized bending, light intensity.

Abstract

Single-mode optical fibers are widely used in modern communication systems due to their high data transmission capacity and low signal attenuation. However, the physical condition of the optical fiber, such as bending caused by mechanical pressure, can affect transmission performance. This research aims to analyze the effect of pressurized bending on single-mode optical fibers and its impact on the attenuation of transmitted light intensity. Experiments were conducted by varying the bending radius and pressure applied to the optical fiber to measure changes in the received light intensity. The results show that as the bending radius decreases and the applied pressure increases, the attenuation of light intensity increases significantly. The reduction in light intensity occurs due to the leakage of light modes from the fiber core as a result of physical deformation in the fiber structure. These findings are important for designing more efficient and resilient optical fiber installations, especially in environments prone to physical pressure and bending.

Downloads

Download data is not yet available.

References

[1] Aryza, S., Lubis, Z., & Lubis, S. A. (2020). Penguatan Industri 4.0 Berbasiskan Arduino Uno Dan GSM SIM900A DiDalam Pintu Geser. JET (Journal of Electrical Technology), 5(2), 80-87.
[2] Aryza, S., Pratama, S., & Ikbal, M. (2022). An Enhance System Smart Toilet Based On Recycle Green Control. Infokum, 10(02), 1156-1163.
[3] B. Widiyatmoko et al., “Study of Microbending Loss Single Mode Optic Fiber in Sand Powder Against Pressure,”Journal of Technomaterials Physics, vol. 3, no. 1, pp. 65-73, Talenta Publisher, 2021
[4] B.Satria, Alam, H., & Rahmaniar, R. (2023). DESAIN ALAT UKUR PENCEMARAN UDARA PORTABEL BERBASIS SENSOR MQ-135 DAN MQ-7. ESCAF, 1278-1285.
[5] Fiber Optic Cable Types –Multimode and Single Mode, RF Industries, San Diego, 2019.
[6] G.P. Agrawal, “Fiber-Optic Communication Systems,”ed. 3, John Wiley & Sons, Inc., New York, 2002
[7] Fitriawan, Ahmad Surya Arifin, Danny Mausa, Agus Trisanto. “Performance Measurement of ZigBee Based Wireless Sensor Networks”. Seminar Nasional FORTEI. Pontianak. 2015
[8] Helmy Fitriawan, Danny Mausa, Ahmad Surya Arifin, Misfa Susanto. “Realization of ZigBee Wireless Sensor Networks For Temperature and Humidity Monitoring”. Proceeding of International on Electrical Engineering, Computer Science and Informatics (EECSI). Palembang. 2015
[9] H. Hamdani, dkk (2022). An Enhance Of Renew Source For Homes. Budapest International Research and Critics Institute Journal ( BIRCI-Journal. 5(3)
[10] Hamdani, H., Sastra, A., & Firmansyah, D. (2023). Kajian Pembangunan Lift Barang Pintar Kapasitas 50 Kg Dengan Pembangkit Listrik Tenaga Surya (PLTS). INTECOMS: Journal of Information Technology and Computer Science, 6(1), 429-433.
[11] Karl, Holger., Willig, Andreas. Protocol and Architectures for Wireless Sensor Networks. John Willey and Sons. 2005
[12] N.Kristoffel, “Total Internal Reflection and the Related Effects,”Proceedings of Tartu State University, No. 42, pp. 94-112, 1956(Source: https://arxiv.org/pdf/1403.4468.pdf).
Published
2024-11-21
How to Cite
Alfredo Bangkit H Parapat, Solly Aryza, & Amani Darma Tarigan. (2024). An Effect Of Pressure Bending In Single Mode Optic Fiber On Light Intensity Attenuation. Jurnal Scientia, 13(04), 1660-1668. Retrieved from https://infor.seaninstitute.org/index.php/pendidikan/article/view/2671

Most read articles by the same author(s)

1 2 > >>